26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations. Document Name: SAE J Test for Motor Vehicle Lighting Devices and Components CFR Section(s): 49 CFR S (e) Standards Body: Society of. SAE J Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than mm in Overall Width.
|Published (Last):||11 August 2006|
|PDF File Size:||6.5 Mb|
|ePub File Size:||18.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
McKale, General Motors Corp. The sae j575 sections describe Individual tests which need not be performed In any particular sequence. For devices with an interior volume greater than mL, the maximum allowable moisture accumulation in the test device shall be 0.
China Lib SAE J Rain Test Equipment – China Rain Test Equipment, SAE J Rain Test Equipment
This includes the humidity-heat test, humidity-frost cycle test and the temperature alternating test. Unless otherwise specified, this Intersection shall be parallel to the longitudinal axis sae j575 the vehicle in the case of the designed operating position of front or rear device.
Sae j575 Executive Director office saf the federal register washington, d. This technical report provides standardized laboratory tests, test methods, and requirements applicable to many of the lighting devices and components covered by SAE technical reports.
If such corrosion is found, the affected test s shall eae performed on the corrosion test sample and the results recorded. Ssae following equipment shall be used to sae j575 the photometric measurements: A’devlce specifically designed to support the lighting device In its designed operating position during- laboratory testing. All sample devices may be tested only to the Water Spray Test 4. The acceleration component measured shall be in the direction of table travel.
The moisture j57 is not required for sealed beam units. This test evaluates the ability of the sample device to resist moisture sae j575 -from a sae j575 spray sae j575 determines the drainage capability of those devices with drain holes or other exposed openings In the device.
VDT Dust test chamber according to standard SAE J575
Search the history of over billion web pages on the Internet. The vertical axis of the goniometer in F1g. All drain holes shall be closed. Also, determine if the luminous saee values between the specified test points are less than the lower of the.
Wright, General Motors Corp. Devices with multiple sae j575 combinations shall be tested with all functions simultaneously operating as specified, except for back-up sae j575. The sae j575 of the tests may be expedited by performing the tests simultaneously on separately mounted.
Weiss weathering and IP sse chambers. This test evaluates the ability of the sample device to resist damage from vibration-Induced stresses. Full text of ” SAE J Test Eq ui pment: Cracking or rupture of parts of the device affecting Its mounting shall also constitute a failure.
All drain, j5575 and other openings shall remain open. Each sample shall be securely mounted on a test fixture in its designed sae j575 position and shall include all sae j575 equip- ment necessary to eae the device in its normal manner. The angle between the vertical plane and the projection of.
This test is not intended to provide a com- plete test on the device seals sae j575 excludes drain holes see Moisture Test 4. The dust shall be allowed to settle between the agitation periods. The photometer sensor used to make the photometric measurements shall have the- sae j575 characteristics: A sample device as mounted on sae j575 test fixture defined in 2.
If a portion of the device 1s completely protected in service such as trunk mounted lampsthat portion shall be covered to- prevent salt fog entry during the salt exposure. Sae j575 warpage is observed that could result in failure of other tests eae in section 4 of this technical report, the test s shall be performed on the warpage test sample and the results recorded. Stop-Turn Signal Functions which are optically h575 shall be tested as a j75 sae j575 only. This angular direction is defined sae j575 follows: If such corrosion Is found, the affected test s shall be performed on the corrosion test sample and sae j575 results recorded.
If the measured moisture accumulation exceeds 2 mL, the Interior volume of the sample device shall be measured and the results recorded.
Devices which have a portion completely protected In service such as trunk, mounted lamps shall sae j575 that part of the device covered to prevent moisture entry during the test.
With 21 companies in 15 countries at 40 locations. Sae j575 which have a portion completely protected in service such as trunk mounted lamps shall have that part of the device covered to prevent moisture entry during the test.
Sae J Rain Test Chamber, Sae J Rain Test Chamber Suppliers and Manufacturers at
The dust test is not required for sealed beam units. Devices designed for use in both 6 V and 12 V systems shall be tested with 12 V bulbs. The j557 machine output wave form shall be sinusoidal with a sae j575 permissible harmonic distortion as shown sae j575 Fig.
A device using a bulb sae j575 a major and minor light source may be oriented with respect to its major light source. All sample devices may be tested only to the Dust Exposure Test 4.